Refer to the example. Please be sure that all screws are fastened, and that there are no loose screws. Please be sure that all connectors are inserted, and that there are no imperfect insertion. Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc. Please check that neither solder debris nor screws remain inside the product. Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one. When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure.
Please exchange the power cord if necessary. When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. Please pay attention to your surroundings and repair safely. To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification. For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper.
Lubricants, Glues, and Replacement parts. Use grease and adhesives that are equal to the specified substance. Make sure the proper amount is applied. Shipping mode and Shipping screws. To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be. Please be sure to follow this method especially if it is specified in this manual. Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs.
Use to connect to the input connectors of external effectors or other similar components. Use to attenuate the level of the master 1 and master 2 outputs.
Attenuation can be set to 0 dB, —3 dB, or —6 dB. Always turn off the power switch and disconnect the power plug from its outlet when making or changing connections. Unbalanced output supporting RCA-type plug. This is a coaxial digital output connector, supporting RCA plugs. The signal from the effector will be input to both L and R channels. Use to adjust the volume of microphone 1. Use to adjust the volume of microphone 2. Use to adjust the treble high-range frequencies of microphones 1 and 2.
Use to adjust the bass low-range frequencies of microphones 1 and 2. Microphone sound is output; when sound is input to a connected microphone, the TALK OVER function operates and all sound other than that from the microphone is attenuated by 20 dB. Use to adjust the input level for each channel. Use to adjust the treble high-range frequency sound for each channel. Use to adjust the mid-range frequency sound for each channel.
Use to adjust the bass low-range frequency sound for each channel. If multiple buttons are pressed simultaneously, the selected audio sources are mixed. Press the button once more to cancel the selected source. Unselected buttons glow darkly, while selected source buttons light brightly.
The button lights when set to ON. This switch allows the user to select from two types of channel fader curve response. This setting is applied equally to channels 1 to 4. This switch allows the user to select from three types of cross fader curve response. As soon as the cross fader lever leaves the [ A ] side, the [ B ] channel sound is produced.
Use to adjust the master output level. These segment indicators display the output level from L and R channels. The indicators have a two-second peak hold. This dial is used to adjust the booth monitor output volume. The volume can be adjusted independently of the master output level. When power is first turned ON, defaults to effect frequency filter and the button indicator lights. When manual filter is selected, the button indicator does not light.
A, CF. Use to select the channel to which effects are applied P. When [ MIC ] is selected, effects are applied to both microphone 1 and microphone 2. Adjusts time parameter for selected effect P. When set to effect OFF, the button indicator lights. When effects are enabled ON , the button flashes.
Text display 7 characters displays effect name as shown in accompanying table. Also, when one of the change operations is performed as noted in the table, the corresponding characters are displayed for two seconds, after which the display returns to the original effect name. If the BPM count cannot be detected automatically, the display will flash at the previously detected value.
Displays parameters designated for each effect. When the beat select buttons BEAT , are pressed, the corresponding beat multiple change is displayed for two seconds. If the beat select buttons BEAT , are used to designate a value outside the parameter range, the current number will flash but will not change. The lower row is lighted constantly. When the parameter 1 location approaches a threshold value, the corresponding indicator is lighted.
When the parameter 1 is between threshold values, the. Although the display includes seven actual indicators, the values of the two ends can also be considered to represent indicators, with the result that nine positions can be logically assumed.
When the values are at the two ends, no indicators light. When the CD player assigned to cross fader channel A is set to standby at a cue point, moving the cross fader lever from the right.
B side toward the left A side automatically starts play on the channel A CD player. When the cross fader lever reaches the left A side, the CD player assigned to channel B goes to back cue returns to cue point. Also, when the CD player assigned to channel B is set to standby at a cue point, moving the cross fader lever from the left A side to the right B side automatically starts playback on the channel B CD player.
When the cross fader lever reaches the right B side, the CD player assigned to channel A goes to back cue returns to cue point. START 1 1, 2. Additionally, by adjusting the parameters for each effects, a wide range of effects can be produced. A low-pass filter effect or high-pass filter effect can be created with the manual filter or effect frequency filter depending on the positioning of the FREQUENCY dial. Additionally, by combining beat effects with the manual filter or effect frequency filter, a wide range of effects can be created.
Short delay. Phase shift. Generates sound effect resembling that produced by a robot. By connecting a sampler or effector, a wide variety of other effects can be created. Beat effects allow the instant setting of effect times in synch with the BPM beats per minute , thus allowing the production of a wide variety of effects in synch with the current rhythm, even during live performances. The BPM of the input music signal is detected automatically.
The use of a substitute replacement component which. Product Safety is continuously under review and new. For the latest. A subscription to, or additional copies of,. This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to. This service manual is intended for qualified service technicians ; it is not meant for the casual. Qualified technicians have the necessary test equipment and tools, and have been.
Improperly performed repairs can adversely affect the safety and reliability of the product and may. If you are not qualified to perform the repair of this product properly and safely, you.
In this manual, procedures that must be performed during repairs are marked with the below symbol. Please conform to product regulations such as safety and radiation regulations , and maintain a safe servicing environment by.
Refer to the example. When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure. To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper. Lubricants, Glues, and Replacement parts.
Use grease and adhesives that are equal to the specified substance. Shipping mode and Shipping screws. To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be. Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting.
0コメント